Aries-automotive B35-4013 Bedienungsanleitung PDF herunterladen

3” BULL BAR

2011-15 CHEVY SILVERADO/GMC SIERRA 2500/3500

Page 1 of 3 3/18/14 (DP)

PARTS LIST:

3in Bull Bar Assembly

12mm x 32mm OD x 3mm Flat Washer

Driver/left Frame Bracket

12-1.75mm Nylon Lock Nut

Passenger/Right Frame Bracket

10-1.5mm x 30mm Hex Bolt

Driver/left Bull Bar Mounting Bracket

10mm x 27mm OD x 3mm Flat Washer

Passenger/right Bull Bar Mounting Bracket

10-1.5mm Nylon Locknut

12-1.75mm x 35mm Bolt Plates

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. CUTTING MAY BE REQUIRED.

INSTALLATION MAY INTERFERE WITH BUMPER MOUNTED PARKING SENSORS.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not

required, but strongly recommended. If local/state law requires a front license plate, license plate

relocation kit is available.

3. Starting at the driver side, remove the factory tow hook if equipped, (Figures 1A & 1B). NOTE: This

Bull Bar is not compatible with the factory tow hooks and they will not be reinstalled. IMPORTANT: On

some models, with and without tow hooks, the pocket in the plastic bumper may need to be cut out,

(Figure 1A). Use a sharp knife or hacksaw blade and carefully cut out the pocket to clear the Bull Bar

Brackets. Only cut enough to clear the Brackets.

4. Insert (1) 12mm Bolt Plate, (Figure 3A), into the end of the frame channel, (Figure 2), and out through

the hole in the bottom of the frame. Insert a second Bolt Plate into the frame and out the hole (for tow

hook bolt) through the outer side of the frame, (Figure 3B).

5. Select the driver side Frame Bracket. Refer to illustration above for bracket configuration. Position the

Frame Bracket onto the outside of the frame channel, (Figure 4), and over the (2) Bolt Plates. Secure

the Bracket to the frame and Bolt Plates with (2) 12mm Flat Washers and (2) 12mm Nylon Lock Nuts.

Leave hardware loose at this time.

6. Next, select the driver side Bull Bar Mounting Bracket. Loosely attach the Bull Bar Bracket to the inside

of the Frame Bracket with the included (2) 10mm x 30mm Hex Bolts, (4) 10mm Flat Washers and (2)

10mm Nylon Lock Nuts, (Figure 5). NOTE: On some models, it may be possible or simpler to bolt the

Frame and Mounting Brackets together first and install as one piece. Do not fully tighten hardware.

7. Repeat Steps 3—6 for passenger side Frame and Mounting Bracket installation.

8. With assistance, position the Bull Bar assembly up to the outside of the Mounting Brackets. Attach the

Bull Bar to the Brackets with the included (2) 10mm x 30mm Hex Bolts, (4) 10mm Flat Washers and (2)

10mm Nylon Lock Nuts, (Figure 6).

9. Level and adjust the Bull Bar and tighten all hardware.

10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Passenger/right Side

Frame Bracket

Driver/left Side

Frame Bracket

Passenger/right Side Bull Bar Bracket

Driver/left Side Bull Bar Bracket

(4) 12mm Bolt Plates

1 2 3

3” BULL BAR 1

Inhaltsverzeichnis

Seite 1 - 3” BULL BAR

3” BULL BAR 2011-15 CHEVY SILVERADO/GMC SIERRA 2500/3500 Page 1 of 3 3/18/14 (DP) PARTS LIS

Seite 2

3” BULL BAR 2011-15 CHEVY SILVERADO/GMC SIERRA 2500/3500 Page 2 of 3 3/18/14 (DP) To protect your

Seite 3

3” BULL BAR 2011-15 CHEVY SILVERADO/GMC SIERRA 2500/3500 Page 3 of 3 3/18/14 (DP) Driver Side Inst

Kommentare zu diesen Handbüchern

Keine Kommentare

Aries-automotive B35-4013 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Aries-automotive B35-4013 herunter. Aries Automotive B35-4013 User Manual [en] [fr] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Aries-automotive B35-4013