Aries-automotive 203040-2 Bedienungsanleitung PDF herunterladen

Page 1 of 4

2009-10 FORD F-150 REGULAR CAB

PARTS LIST:

1 Driver/Left Sidebar 4 12mm ID x 30.1mm OD x 3mm Flat Washers

1 Passenger/Right Sidebar 4 12mm Lock Washers

1 Driver/Left Front Mounting Bracket 4 12mm Hex Nuts

1 Passenger/Right Front Mounting Bracket 4 10-1.50mm x 35mm Hex Bolts

1 Driver/Left Rear Mounting Bracket 6 10mm x 30mm OD x 2.1mm Flat Washers

1 Passenger/Right Rear Mounting Bracket 4 10mm Lock Washers

2 12mm x 40mm x 10mm Nut and Bolt Plate 2 10mm Hex Nuts

2 12mm x 40mm Bolt Plates 4 8-1.25mm x 30mm Hex Head Bolts

4 11mm Plastic Retainers 4 8mm ID x 22mm OD x 1.5mm Flat Washers (Outer)

2 9mm Plastic Retainers 4 8mm ID x 17.1mm OD x 1.3mm Flat Washers (Inner)

4 1/2" x 2” Hex Head Bolts 4 8mm Lock Washers

4 1/2” x 1-1/4” OD x 3/32” Flat Washers 4 8mm Hex Nuts

4 1/2” Lock Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. DRILLING IS REQUIRED. ASSISTANCE

RECOMMENDED.

2. Starting at the front of the driver side of the vehicle, remove the plastic pin, the two small hex bolts and

the metal clips holding the bottom of the fender to the body, (Figure 1A). NOTE: Use a small flat

screwdriver to spread the clip apart for easy removal. Due to body panel misalignment from the factory,

it may be necessary to open these holes slightly with a 3/8" drill bit, (Figure 1B).

3. Next, locate the round and square holes in the floor panel next to the body mount, (Figure 2). Select (1)

12mm x 40mm x 10mm Nut and Bolt Plate and thread (1) 11mm Plastic Retainer part way onto it. Insert

the Nut and Bolt Plate into the square hole in the floor. Line up the nut on the Nut and Bolt Plate with

the round hole. IMPORTANT: The Plastic Retainer is designed to prevent the Bolt Plate from falling

into the body cavity and to aid in mounting the Bracket. After inserting, thread the Plastic Retainer down

but leave it loose enough to move the Nut and Bolt Plate around during installation of the Mounting

Bracket. NOTE: For passenger side installation, remove the ground strap next to the mounting holes.

4. Select the driver side front Mounting Bracket and hold it at a slight angle against the body. Move the top

of the Bracket into position with the threaded end of the Nut and Bolt Plate lined up with the T-Slot in

the Bracket. The top of the Bracket is designed to fit snug in position between the body mount and the

lip on the body so it may take a couple of tries to get the Bracket into the correct position, (Figure 3).

INSTALLATION INSTRUCTIONS

203040/203040-2

Driver side Rear

Mounting Bracket

Driver side

Front

Mounting

Bracket

Passenger

side Front

Mounting

Bracket

Passenger side

Rear Mounting

Bracket

12mm x 40mm

x 10mm Nut

and Bolt Plate

12mm x 40mm Bolt

Plate (Pictured with

plastic retainer

attached for

example only)

1 2 3 4

INSTALLATION INSTRUCTIONS 1

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

Page 1 of 4 2009-10 FORD F-150 REGULAR CAB PARTS LIST: 1 Driver/Left Sidebar 4

Seite 2

Page 2 of 4 Once the top of the Bracket is properly lined up in the T-Slot, rotate the bo

Seite 3

Page 3 of 4 Driver Side Installation Pic

Seite 4

Page 4 of 4 1/2” x 2” Hex Bolts1/2” Lock Washers 1/2” Flat Washers 12mm Bolt Plate with P

Verwandte Modelle: 203040

Kommentare zu diesen Handbüchern

Keine Kommentare

Aries-automotive 203040-2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Aries-automotive 203040-2 herunter. Aries Automotive 203040-2 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 203040

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Aries-automotive 203040-2