Aries-automotive 203033-2 Bedienungsanleitung PDF herunterladen

1998-09 MAZDAB-SERIES P/U SUPER CAB

1998-09 RANGER EDGE SUPER CAB

Part # 203033 / 203033-2

1,2 2 STEP BAR, PASSENGER (1) AND DRIVER

3,4

11 2 1/2-13 X 2.50” HEX HEAD BOLT

12 2 1/2-13 X 2.00” HEX HEAD BOLT

13 4

14 4

15 10 3/8-16 X 1.25” HEX HEAD BOLT

16 16 3/8” FLAT WASHER

17 10 3/8” LOCK WASHER

18 6 3/8-16 HEX NUT

(2)

2 FRONT BRACKET, PASSENGER (3) AND DRIVER (4)

, PASSENGER (5) AND DRIVER (6)

7,8 2 MOUNT PLATEASSEMBLY, PASSENGER (7) AND DRIVER (8)

, PASSENGER (9) AND DRIVER (10)

1/2” FLAT WASHER

1/2” LOCK WASHER

5,6 2 REAR BRACKET

9,10 2 SUPPORT BRACE

QTY

CONTENTS -

TOOLS -

3/4” SOCKET

9/16” SOCKET

9/16” WRENCH

*7/16” DRILL BIT

*DRILL

CENTER PUNCH

HAMMER

RATCHET

TORQUE WRENCH

*NOTE: A SHORT 7/16” BIT WITH A3/8”

SHANK AND ASMALL OR RIGHTANGLE

DRILL MAY BE NECESSARY FOR EASIER

INSTALLATION.

ITEM

5 7 9

6 8

REG. CAB

EXT. CAB

Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely

before beginning.

Attach front brackets and support braces using 3/8” fasteners as shown.

Temporarily attach rear bracket to vehicle through hole as shown. Carefully cut out templates

and align with visible portion of rear bracket. Tape template in place and mark center of top hole with center

punch. Remove template and bracket from vehicle. Drill 7/16” diameter hole at this location.

If hole on rocker panel aligns with T-Slot on mount bracket fasten at this location. Drilling is not re-

quired.

Attach rear brackets to the backside of rocker panel using 3/8” fasteners as shown.

Attach step bars to brackets using 1/2” fasteners as shown.

Make sure step bar and brackets are properly aligned with vehicle and tighten fasteners. Recommended torque

value is 26 Ft. Lbs. for 3/8” fasteners and 64 Ft. Lbs. for 1/2” fasteners.

SEE FIGURES 1 THROUGH 3.

SEE FIGURE 4.

NOTE:

SEE FIGURE 5.

SEE FIGURE 6.

FINISH PROTECTION- ARIES PRODUCTS HAVE A HIGH FINISH THAT MUST BE MAINTAINED SUCH AS

ANY OTHER HIGH FINISH PRODUCT ON THE VEHICLE. PROTECT THE FINISH WITH A NON-ABRASIVE

AUTOMOTIVE WAX. THE USE OF SOAP, POLISH, OR WAX THAT CONTAINS ABRASIVES IS DETRIMENTAL,

AS THE COMPOUNDS SCRATCH THE FINISH AND OPEN IT TO CORROSION.

DISCLAIMER- BUYER ASSUMES ALL RISK AND LIABILITY WHATSOEVER FROM THE INSTALLATION

AND USE OF ARIES PRODUCTS. ARIES PRODUCTS ARE SOLD AS DECORATIVE ACCESSORIES AND

SHOULD NOT BE RELIED UPON AS PROTECTION FOR THE VEHICLE OR OCCUPANTS IN THE EVENT OF A

COLLISION OR ROLL OVER. ARIES AUTOMOTIVE ASSUMES NO LIABILITY FOR INJURY, LOSS.

Step 1.

Step 2.

Step 3.

Step 4.

Step 5.

Step 6.

1 2

ALIGN TEMPLATE 2
DRILL IF REQUIRED 2

Inhaltsverzeichnis

Seite 1

1998-09 MAZDAB-SERIES P/U SUPER CAB1998-09 RANGER EDGE SUPER CAB Part # 203033 / 203033-21,2 2 STEP BAR, PASSENGER (1) AND DRIVER3,411 2 1/2-13 X 2.5

Seite 2 - DRILL IF REQUIRED

4123ALIGN TEMPLATE6DRILL IF REQUIRED57161716161211151718171313151814141165169315INSTALLATION VIEW OF PASSENGER SIDE SHOWN, DRIVER SIDE OPPOSITECustome

Verwandte Modelle: 203033

Kommentare zu diesen Handbüchern

Keine Kommentare

Aries-automotive 203033-2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Aries-automotive 203033-2 herunter. Aries Automotive 203033-2 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 203033

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Aries-automotive 203033-2