Aries-automotive TB45-5005 Bedienungsanleitung PDF herunterladen

PART # TB45-5005 / 45-5005

Page 1 of 5

PARTS LIST:

Qty Description Qty Description

1 Bull Bar 10 12mm Lock Washers

Upper Frame Mounting Brackets (for trucks

without tow hooks only)

8 12-1.75mm Hex Nuts

1 Driver/Left Lower Frame Mounting Bracket 2 10-1.5mm x 35mm Hex Bolts

1 Passenger/Right Lower Frame Mounting Bracket 2 10mm Lock Washers

1 Driver/Left Support Bracket 4 10mm x 30mm OD x 3mm Flat Washers

1 Passenger/Right Support Bracket 2 10-1.5mm Hex Nuts

12-1.5mm x 30mm Fine Thread Hex Bolt (for

trucks without tow hooks only)

2 6mm x 20mm Button Head Allen Bolt S/S

4 12-1.75mm x 35mm Hex Bolts 4 6mm x 12mm OD x 1.4mm Flat Washers S/S

14 12mm x 30.1mm OD x 3.1mm Flat Washers 2 6mm Nylock Hex Nut S/S

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED.

ASSISTANCE IS RECOMMENDED.

2. Starting at the underside of the front bumper, carefully remove the plastic splash guard. NOTE:

Depending on the model of truck, the splash guard may be attached to the bottom of the truck with

hex bolts. There are also several two-piece plastic push-in clips across the back, behind the

bumper cover holding the splash guard up to the cover, (Figure 1A). First, locate the clips behind

the bumper cover. Pry the center pin of the clip up with a small flat blade screwdriver and remove

the entire clip, (Figure 1B). The splash guard may also be attached with rivets or hex bolts at the

corners of the bumper cover. If the guard is fastened with rivets, once all of the other hardware

has been removed, hold the bumper cover in place and firmly pull the splash guard from the rivet.

Remove the rivet from the bumper cover and move the splash guard to a clean stable work area.

Pay close attention to the type and location of all factory hardware for reinstallation.

3. From underneath the front of the vehicle, determine if the truck is equipped with or without tow

hooks.

INSTALLATION INSTRUCTIONS

09-ON DODGE RAM

Passenger Side

Lower Frame

Mounting Bracket

Driver Side Lower

Frame Mounting

Bracket

Passenger Side

Support Bracket

(see note below)

Upper Frame

Mounting

Bracket (use

on trucks

without tow

hooks only)

Upper Frame

Mounting

Bracket (use

on trucks

without tow

hooks only)

Driver Side Support Bracket

(Support Brackets shown in non-

tow hook direction. Reverse

direction for tow hook equipped

vehicles)

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

PART # TB45-5005 / 45-5005 Page 1 of 5 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Mount

Seite 2 - Page 2 of 5

Page 2 of 5 For models without tow hooks: A. Select one of the Upper Frame Brackets and the driver side Lower Frame Mounting Bracket. Bolt the

Seite 3

Page 3 of 5 10. Reinstall the Bull Bar described in Step # 5, (Figure 9). NOTE: For models with tow hooks-Attach the front of the Support Bracket

Seite 4

Page 4 of 5 Driver Side Installation Pictured Fig 4 Fig 5 Hold the splash guard up to t

Seite 5

Page 5 of 5 Driver Side Installation Pictured Installation pictured without the splash guard for illustration Fig 7 If required, repl

Kommentare zu diesen Handbüchern

Keine Kommentare

Aries-automotive TB45-5005 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Aries-automotive TB45-5005 herunter. Aries Automotive TB45-5005 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Aries-automotive TB45-5005